•  
    Results 1 to 9 of 9

    Thread: How to unclip O2 sensor connector? Can't get it to budge at all?

    1. #1
      What's wrong with my car?
      Join Date
      Apr 2013
      Location
      Ottawa
      Posts
      4
      Garage empty: add car
      Thanks
      0
      Thanked 0 Times in 0 Posts

      How to unclip O2 sensor connector? Can't get it to budge at all?

      Hello,

      I have been reading these forums the last few days to try and get my car to pass the new emissions test. I have determined that it is the upstream O2 sensor that needs to be replaced but when I went to replace it I encountered a problem right away with removing the connector. Here are a few pictures.

      Name:  IMG00185-20130415-1050.jpg
Views: 8948
Size:  282.4 KBName:  IMG00184-20130415-1049.jpg
Views: 11128
Size:  285.0 KB

      I have tried pushing in and pulling the black tab on the underside (picture at right) but can't budge it at all? Should I be doing something to the red tab on top at the same time? I tried a search here but nothing came up.

      Thanks!



    2. #2
      Lifetime owner
      Join Date
      Sep 2008
      Location
      Pittsburgh
      Posts
      8,013
      Garage empty: add car
      Thanks
      2
      Thanked 171 Times in 142 Posts
      push the clips toward each other, and then push the black tab down and pull them apart..

      the plastic often gets brittle, so you might need to put a small screw driver in there to bend the plastic off the tab (what the black tab should do).


    3. #3
      I'll keep it and add a turbo
      Join Date
      Mar 2013
      Location
      MN
      Posts
      102
      Thanks
      0
      Thanked 0 Times in 0 Posts
      doubledown-

      use compressed air (protect eyes) to blow the dust/grit out of the section where they slide together and around the locking tabs. HTHY

    4. #4
      What's wrong with my car?
      Join Date
      Apr 2013
      Location
      Ottawa
      Posts
      4
      Garage empty: add car
      Thanks
      0
      Thanked 0 Times in 0 Posts
      petrified.rabbit So I tried pushing together the clips then pushing the black tab down and still didn't have any luck even after using a small screwdriver (I'll try an even smaller screwdriver tomorrow)

      JusteR I am going to get some compressed air tomorrow at lunch and try that as well as the above method.

      Thanks very much to the both of you for your replies and I will update once I get back at er tomorrow!

    5. #5
      What's wrong with my car?
      Join Date
      Apr 2013
      Location
      Ottawa
      Posts
      4
      Garage empty: add car
      Thanks
      0
      Thanked 0 Times in 0 Posts
      So after trying the above solutions I only managed to budge the underside (with the black tab). Should I be doing something with the red tab on top? (it looks like it could move but can't move mine) I managed to jam a micro flat head screw driver between the male and female parts except i couldn't near the red tab on top which makes me wonder if it needs to be moved? I wonder if they could be melted together somehow?
      Last edited by doubledown; 04-16-2013 at 03:34 PM.

    6. #6
      I'll keep it and add a turbo
      Join Date
      Mar 2013
      Location
      MN
      Posts
      102
      Thanks
      0
      Thanked 0 Times in 0 Posts
      Don't worry about the red tab. keep wiggling, it'll come apart... unless it's been super-glued. Finesse will come with experience BTDT broke a few.

    7. #7
      What's wrong with my car?
      Join Date
      Apr 2013
      Location
      Ottawa
      Posts
      4
      Garage empty: add car
      Thanks
      0
      Thanked 0 Times in 0 Posts
      Thanks for all the help JusteR! The relief when it finally came apart was amazing. Now to get the other end out of the manifold!

    8. #8
      What's wrong with my car?
      Join Date
      Dec 2013
      Location
      florida
      Posts
      1
      Thanks
      0
      Thanked 0 Times in 0 Posts
      would like to get a car fax on my aveo, it is sitting in the shop now, after just buying it for fuel pump/catalyic converter. Place I bought from did give out a car fax. It was a nice running car till this happened. Also rear wheels have locked up..

    9. #9
      What's wrong with my car?
      Join Date
      Jan 2014
      Location
      Canada
      Posts
      7
      Garage empty: add car
      Thanks
      0
      Thanked 0 Times in 0 Posts
      Rear shoe automatic adjuster is either jammed or a shoe has fallen off inside the rear drum, jamming the wheel. The rear brakes are essentially stuck on. Happened to my wife. If you need to take it somewhere to be fixed, save yourself a tow and remove the rear wheel and drum, take out the rear brake pads and shoes, put the drum and wheel back on and drive it whereever you need to go. Just remember you'll only have front brakes and they don't grab until the pedal is almost to the floor so be careful.





    Similar Threads

    1. how to disassemble a weatherpak connector?
      By Daox in forum Troubleshooting and Maintenance
      Replies: 7
      Last Post: 04-21-2013, 05:20 AM
    2. Coolant Connector removal?
      By jonota in forum Engine & Drivetrain
      Replies: 4
      Last Post: 04-20-2013, 02:07 AM
    3. Unconnected wire connector under steering wheel - cruise control?
      By nsa_sailor in forum Troubleshooting and Maintenance
      Replies: 2
      Last Post: 04-15-2013, 03:16 AM
    4. Replies: 6
      Last Post: 04-02-2012, 11:39 PM
    5. Fog Light Connector
      By auraxr in forum General Discussion
      Replies: 1
      Last Post: 02-18-2012, 05:14 AM

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •