Headlight Painting aka "Joey Mod" w/Pics 56K Warning

User avatar
WOLFMAN AK907
Posts: 1008
Joined: Sat Sep 12, 2009 2:38 am
Location: Fairbanks, Alaska
Contact:

Headlight Painting aka "Joey Mod" w/Pics 56K Warning

Postby WOLFMAN AK907 » Fri Oct 16, 2009 12:38 am

Ok, so I know there is already a topic like this that we put in the Exterior FAQ, but here's some pictures that walk you through it with a few pointers.
Remove the 3 bolts on each headlight and remove the housing. Take out your headlight bulb, the ruber gasket and all 3 rubber breather tubes on the housing.
Image
Your headlights are out.
Image
Once your oven is pre-heated to 170*F on bake, put your headlight in for 10-12 minutes.
Image
When you pull it out pry the little clips holding the lense to the housing with a small screwdriver and pry the housing from the lense with all your man power.
Image
Image
Where the chrome frame attaches to the clear lense there should be quite a few little silver screws holding them together, remove them all so you can take the turn-signal reflecter side out and you just have the frame you want to paint now. This is where you have to make a choice about what you're going to do with the reflector in you headlight housing. You can remove it like I did, tint it with some form of transllucent paint or you can remove it and replace it once you've painted your chrome black. I left mine out completely cuz' I hated them. Clean it with a wax, grease and oil remover and do not touch it with your fingers or your paint will bubble. For paint I used Dupli-Color Black Low-Gloss Engine Enamel. Start painting.
Image
Nice even light coats.
Image
Let it dry for a while, don't be in a rush even though it looks reall cool now.
Image
Once dry, put it all back together the way it was, but don't try to get a tight fit with the 2 pieces yet. Make sure before you put it all back together that the inside of your lense is clean, so you dont have fingerprints or smudges on the inside of your headlights. Put it back in the oven for 10-12 minutes, run a bead of clear RTV silicone around the whole thing and smash it back together until it clips in. Make sure you don't get any of your silicone on the lense cuz' it's a bitch to get off, if you do clean it immediately with windex and a paper towel while it's still wet.
Image
Finished product:
Image
Put it all back on your car and bolt em' down. If you left the reflector removed you will need to get a pair of 194 amber bulbs for your sidemarkers.
Image
Image
Image
Image
No light output lost.
Image
Have fun and enjoy your new custom $10 headlights.

Farthest North Aveo: Fairbanks, Alaska
ImageImageImage

User avatar
Petrified.Rabbit
Posts: 1254
Joined: Sat Sep 12, 2009 12:08 am
Location: Pittsburgh

Re: Headlight Painting w/Pics 56K Warning

Postby Petrified.Rabbit » Fri Oct 16, 2009 8:25 am

good work, i see you didnt take out the 10 mm bolt right beside the turn signal bulb either.

looks good though.

it should be OEM with projectors...

User avatar
Chris
Posts: 88
Joined: Mon Sep 14, 2009 12:33 pm
Location: Aberdeen, Scotland.

Re: Headlight Painting w/Pics 56K Warning

Postby Chris » Fri Oct 16, 2009 9:29 am

Could have done with this tutorial before i done mine. Never mind! Lookin good!
The only modified Aveo in Scotland!

User avatar
Nemasys
Posts: 206
Joined: Sun Sep 13, 2009 8:38 pm
Location: Ontario, Canada
Contact:

Re: Headlight Painting w/Pics 56K Warning

Postby Nemasys » Fri Oct 16, 2009 10:24 am

Very nice! Looks clean and flows well with the color of the car
2004 Hatchback 2.0L Turbocharged
- T3/T4 T04E .60 A/R Compressor
- HKS SSQV, OBX Wastegate
- FMIC with 2.5" piping
- Tuned with Megasquirt II v3.57

User avatar
WOLFMAN AK907
Posts: 1008
Joined: Sat Sep 12, 2009 2:38 am
Location: Fairbanks, Alaska
Contact:

Re: Headlight Painting w/Pics 56K Warning

Postby WOLFMAN AK907 » Fri Oct 16, 2009 12:15 pm

Thanks, rabbit what 10mm bolt are you speaking of? You mean on the back of the housing? No, I didn't...what's it do?
Farthest North Aveo: Fairbanks, Alaska
ImageImageImage

User avatar
Chris
Posts: 88
Joined: Mon Sep 14, 2009 12:33 pm
Location: Aberdeen, Scotland.

Re: Headlight Painting w/Pics 56K Warning

Postby Chris » Fri Oct 16, 2009 12:18 pm

WOLFMAN AK907 wrote:Thanks, rabbit what 10mm bolt are you speaking of? You mean on the back of the housing? No, I didn't...what's it do?

I know my lights are different but the only 10mm bolts I took out were the 3 holding them in. I'm confused too!
The only modified Aveo in Scotland!

User avatar
WOLFMAN AK907
Posts: 1008
Joined: Sat Sep 12, 2009 2:38 am
Location: Fairbanks, Alaska
Contact:

Re: Headlight Painting w/Pics 56K Warning

Postby WOLFMAN AK907 » Fri Oct 16, 2009 12:20 pm

I think he means the one that holds the relector housing for the actual headlight. I didn't even really think to remove to be honest...seemed like more work to me.
Farthest North Aveo: Fairbanks, Alaska
ImageImageImage

User avatar
WOLFMAN AK907
Posts: 1008
Joined: Sat Sep 12, 2009 2:38 am
Location: Fairbanks, Alaska
Contact:

Re: Headlight Painting w/Pics 56K Warning

Postby WOLFMAN AK907 » Fri Oct 16, 2009 12:45 pm

Petrified.Rabbit wrote:good work, i see you didnt take out the 10 mm bolt right beside the turn signal bulb either.

looks good though.

it should be OEM with projectors...

I wish I had projectors...I hope the new Lova we saw pictues of comes with aveo5 projectors on it. I would be getting a set of those. They'd probably be like 500 bucks though.
Farthest North Aveo: Fairbanks, Alaska
ImageImageImage

User avatar
Petrified.Rabbit
Posts: 1254
Joined: Sat Sep 12, 2009 12:08 am
Location: Pittsburgh

Re: Headlight Painting w/Pics 56K Warning

Postby Petrified.Rabbit » Fri Oct 16, 2009 1:45 pm

WOLFMAN AK907 wrote:Thanks, rabbit what 10mm bolt are you speaking of? You mean on the back of the housing? No, I didn't...what's it do?



it you look at the picture right after the oven picture, at the + hole for the turn signal bulb, you can see the chrome piece that is attached with the screw. it is part of the chrome surround you painted. (i broke mine too)

but if you looked at the other site like you said you did, i know i posted that i forgot to take it out too..

User avatar
Petrified.Rabbit
Posts: 1254
Joined: Sat Sep 12, 2009 12:08 am
Location: Pittsburgh

Re: Headlight Painting w/Pics 56K Warning

Postby Petrified.Rabbit » Fri Oct 16, 2009 1:47 pm

WOLFMAN AK907 wrote:
Petrified.Rabbit wrote:good work, i see you didnt take out the 10 mm bolt right beside the turn signal bulb either.

looks good though.

it should be OEM with projectors...

I wish I had projectors...I hope the new Lova we saw pictues of comes with aveo5 projectors on it. I would be getting a set of those. They'd probably be like 500 bucks though.


once i get some extra money (after coilovers) i am going to build some projecter headlights,



Return to “Exterior”

Who is online

Users browsing this forum: No registered users and 5 guests