•  
    Results 1 to 7 of 7

    Thread: P0113 (where is the air intake temperature sensor??)

    1. #1
      What's wrong with my car?
      Join Date
      Sep 2017
      Location
      ny
      Posts
      5
      Thanks
      1
      Thanked 0 Times in 0 Posts

      P0113 (where is the air intake temperature sensor??)

      Hello all,

      I have a 2009 4dr hatchback and had numerous codes p0102, 0113. I switched out the air intake pipe and MAF sensor and now I only have P0113. I couldn't find air intake temperature sensor anywhere on the air intake pipe and then read that it is incorporated into the MAF sensor, but I'm still getting p0113. I'm about to rip out the air filter housing to see if anything is there. I'm at a loss now.

      any help is GREATLY appreciated!!!

      thanks in advance



    2. #2
      What's wrong with my car?
      Join Date
      Sep 2017
      Location
      ny
      Posts
      5
      Thanks
      1
      Thanked 0 Times in 0 Posts
      Is it possible that the air intake temp sensor is located on the throttle body itself? The schematics on this car are terrible. I'm pulling everything out now, clean out the throttle body, see what that does.

    3. #3
      Almost time to do my timing belt xintersecty's Avatar
      Join Date
      Sep 2010
      Location
      West Union, SC
      Posts
      1,687
      Thanks
      86
      Thanked 181 Times in 156 Posts
      I think 2009 has a different setup and you're right they are terrible.
      Please do not power off, firmware update pending.....

    4. #4
      Almost time to do my timing belt xintersecty's Avatar
      Join Date
      Sep 2010
      Location
      West Union, SC
      Posts
      1,687
      Thanks
      86
      Thanked 181 Times in 156 Posts
      Found this:

      Note: The intake air temperature sensor is no longer replaced as a separate service item. If
      the intake air temperature sensor is faulty, replacement of the entire air cleaner inlet duct
      will be necessary.
      1. Turn OFF the ignition.
      2. Disconnect the electrical connector from the intake air temperature (IAT) sensor.
      3. Disconnect the breather tube from the air cleaner intake duct.
      4. Loosen the clamps securing the air cleaner intake duct.
      5. Remove air cleaner intake duct.
      Installation Procedure
      © 2010
      Please do not power off, firmware update pending.....

    5. The Following 2 Users Say Thank You to xintersecty For This Useful Post:

      jsauer5 (09-19-2017),MetroMPG (09-19-2017)

    6. #5
      What's wrong with my car?
      Join Date
      Sep 2017
      Location
      ny
      Posts
      5
      Thanks
      1
      Thanked 0 Times in 0 Posts
      I did find that install procedure. I also found online that chevy incorporates IAT sensor with the MAF sensor, so I figured replacing MAF with the p0102 reading would do the trick but not for p0113. I replaced the inlet duct, maf sensor, pulled out the air filter housing, cleaned it. Cleaning the throttle body now. Looking for a schematic for it but nothing is similar. Did a freeze frame on my odb reader and iat sensor is at -40. There are no breather tubes or sockets for an air flow sensor on the inlet duct housing. Only thing connected from the air filter housing to the throttle body is the inlet duct and MAF sensor. Checking MAF connector with a Multi meter now to see if there is a bad wire, connector. This is really a mystery now.

    7. #6
      Administrator MetroMPG's Avatar
      Join Date
      Jan 2007
      Location
      1000 Islands, Ontario, Canada
      Posts
      4,071
      Thanks
      270
      Thanked 121 Times in 102 Posts
      jsauer5 - please post back and let us know how it turns out.

    8. #7
      What's wrong with my car?
      Join Date
      Sep 2017
      Location
      ny
      Posts
      5
      Thanks
      1
      Thanked 0 Times in 0 Posts
      I paid $28 to talk to a chevy tech online. The IAT sensor is built into the MAF sensor, like I thought. He thinks it's a short in the wire or connector. Told me which wires to jump to see if that is it(brown and white) I'm now looking online how to check for wire shorts. visibly, I see nothing out of the ordinary. Nothing burnt, fraid, crumbling, rusting. connector looks good. sprayed some electronic cleaner in it. still the same p0113 code. been looking online and at the part stores for a new connector, but couldn't find anyone who carried it (pepboys, advanced auto, autozone). techs at all 3 places said it would probably be a dealer part......great. going on 2 weeks now. I'm trying 1 more thing, then bringing it in. Oh well, I tried.





    Similar Threads

    1. Cooling temperature sensor
      By urdreamlady in forum Engine & Drivetrain
      Replies: 4
      Last Post: 02-24-2016, 06:09 PM
    2. Coolant temperature sensor
      By Coryb in forum Troubleshooting and Maintenance
      Replies: 20
      Last Post: 02-13-2015, 02:44 AM
    3. ECT Engine coolant temperature Sensor
      By spirlet in forum How-To
      Replies: 1
      Last Post: 03-22-2013, 02:57 PM
    4. Ambient temperature sensor part number?
      By wylee in forum General Discussion
      Replies: 6
      Last Post: 08-23-2011, 03:31 PM
    5. WTB: Intake Air Temperature Sensor
      By y2dgone in forum For Sale / Wanted
      Replies: 14
      Last Post: 04-16-2008, 01:49 PM

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •