•  
    Page 1 of 3 123 LastLast
    Results 1 to 10 of 23

    Thread: Transmission cooler bango connector torque spec?

    1. #1
      What's wrong with my car?
      Join Date
      May 2021
      Location
      South Atlanta, Georgia
      Posts
      25
      Garage empty: add car
      Thanks
      22
      Thanked 1 Time in 1 Post

      Transmission cooler bango connector torque spec?

      There are alot of misinformation about bango fittings . The 2008 CHEVY AVEO automatic transmission cooler is on the radiator with the inlet being a hose with hose clamp and the outlet connected on top side with a hard steel line with a bango fitting.
      Questions:
      #1- What is the torque spec. For the 19mm bango fitting bolt head?
      #2- What size is the crush washers size and /or part number for that particular bango fitting?
      Thank you and AVEO ON!
      JOHN KENDALL



    2. #2
      2004 1.6 Auto Rust Free
      Join Date
      Jun 2019
      Location
      NC
      Posts
      567
      Thanks
      1
      Thanked 59 Times in 55 Posts
      Fitting comes with a new line. Otherwise match it up at a parts house
      https://www.gmpartsdirect.com/oem-pa...e-kit-96536664

    3. #3
      What's wrong with my car?
      Join Date
      May 2021
      Location
      South Atlanta, Georgia
      Posts
      25
      Garage empty: add car
      Thanks
      22
      Thanked 1 Time in 1 Post
      Thanks , I saw the dealer diagram but did not want to buy the hose twice. Last weekend I replaced the radiator because of a leak and this weekend I am installing a new condenser, compressor, and dryer.
      My parts did not show up in time for everything to be done last weekend and I use the car during the week as my big truck is off insurance and tags while the gas prices are high.

    4. #4
      What's wrong with my car?
      Join Date
      May 2021
      Location
      South Atlanta, Georgia
      Posts
      25
      Garage empty: add car
      Thanks
      22
      Thanked 1 Time in 1 Post
      Now I just need to know the Torque specs.

    5. #5
      2004 1.6 Auto Rust Free
      Join Date
      Jun 2019
      Location
      NC
      Posts
      567
      Thanks
      1
      Thanked 59 Times in 55 Posts
      I can’t find one either, but I do know it won’t be a really high spec. If I had to guess I would go around 17-22 foot pounds.

    6. #6
      What's wrong with my car?
      Join Date
      May 2021
      Location
      South Atlanta, Georgia
      Posts
      25
      Garage empty: add car
      Thanks
      22
      Thanked 1 Time in 1 Post
      I found the same size aluminum crush washers at parts store, but it leaked. I need the correct torquefor sealing bango fitting.

    7. #7
      Should I keep it?
      Join Date
      Jan 2019
      Location
      Uruguay
      Posts
      87
      Thanks
      6
      Thanked 1 Time in 1 Post
      Me too.
      When I removed it it was sooo tight. Had to use a breaker bar!

    8. #8
      Should I keep it?
      Join Date
      Jan 2019
      Location
      Uruguay
      Posts
      87
      Thanks
      6
      Thanked 1 Time in 1 Post
      Cleaned up the copper Bangor washers with light sandpaper. Torqued to 27/28 Nm so far and a tiny tiny spot of atf on 1 side of the upper washer.
      Hmm maybe try a pair of new washers?

    9. #9
      Should I keep it?
      Join Date
      Jan 2019
      Location
      Uruguay
      Posts
      87
      Thanks
      6
      Thanked 1 Time in 1 Post
      Anybody know the size of these washers?
      Haven't found the torque settings yet and still leaking with 28nm using the old washers.

    10. #10
      2004 1.6 Auto Rust Free
      Join Date
      Jun 2019
      Location
      NC
      Posts
      567
      Thanks
      1
      Thanked 59 Times in 55 Posts
      Use fine sandpaper on top a piece of glass. That’ll help make them flat and smooth. I have no idea what the OEM part number is.





    Page 1 of 3 123 LastLast

    Similar Threads

    1. Transmission Cooler Lines
      By davesteve in forum How-To
      Replies: 0
      Last Post: 09-08-2021, 08:57 PM
    2. Transmission Cooler Line Assembly Problem
      By aveoriv in forum Technical
      Replies: 2
      Last Post: 06-05-2021, 12:13 AM
    3. Replies: 5
      Last Post: 12-17-2020, 05:01 AM
    4. Ghost Connector - what connector is this??
      By Pootis in forum Technical
      Replies: 4
      Last Post: 08-20-2020, 06:02 AM
    5. Engine/Drivetrain/Front End Torque Spec. Chart
      By 69mock1 in forum Engine & Drivetrain
      Replies: 1
      Last Post: 02-07-2015, 02:10 AM

    Tags for this Thread

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •