2009 Aveo Crankshaft-Camshaft Correlation

[AfterHoursAuto]

We recently had to do a head job on a 2009 Chevy Aveo. The guy never changed his timing belt and ended up bending ALL of the valves when the belt stripped out. We got it all done and back together and now we keep getting a engine code saying theres a correlation problem between the crankshaft and camshafts. I have taken it all back apart 3 additional times after the head was fixed trying to get this straightened out and I am stuck here. Are there any relearn procedures for the Variable Cams? It seems that the phasers/solenoids might keep throwing the exhaust cam out of time? Any help would be greatly appreciated! If you would like to call me my phone number is (517) 442-2054.

[2010AveoLT]

We recently had to do a head job on a 2009 Chevy Aveo. The guy never changed his timing belt and ended up bending ALL of the valves when the belt stripped out. We got it all done and back together and now we keep getting a engine code saying theres a correlation problem between the crankshaft and camshafts. I have taken it all back apart 3 additional times after the head was fixed trying to get this straightened out and I am stuck here. Are there any relearn procedures for the Variable Cams? It seems that the phasers/solenoids might keep throwing the exhaust cam out of time? Any help would be greatly appreciated! If you would like to call me my phone number is (517) 442-2054.

the Cam/Crank Relearn procedure requires a Tech 2 or Aftermarket Equivalent (which can cost upwards of thousands of dollars)

[AfterHoursAuto]

the Cam/Crank Relearn procedure requires a Tech 2 or Aftermarket Equivalent (which can cost upwards of thousands of dollars)

Will a relearn fix my problem? We have access Snap On Modis. Would it be sufficient to do the relearn procedure?

[2010AveoLT]

Will a relearn fix my problem? We have access Snap On Modis. Would it be sufficient to do the relearn procedure?

then you're good to go, as i Believe the Modis actually supports the Cam/Crank Relearn procedure.

[AfterHoursAuto]

then you're good to go, as i Believe the Modis actually supports the Cam/Crank Relearn procedure.

We had that done and it made no difference. Anything else we should try? We tried to go to the dealership but they are over a month out for diagnostic.

[sauceboss]

Any news on what the fix was to this problem? I am having the same issue with my aveo now and can not for the life of me figure out what the problem is.

[AfterHoursAuto]

It is having a hard time starting. Once it starts the idle is up and down, but sounds like its firing on all 4 once it starts. It also bogs down when we give it some gas.

[avguy]

Assuming you've reconnected everything correctely, I'd suspect a timing issue. Did you try a compression and leak down test?

[AfterHoursAuto]

Assuming you've reconnected everything correctely, I'd suspect a timing issue. Did you try a compression and leak down test?

I've set the timing 3 times. I turn it over by hand a few times and it stays in time. I start it and it runs for a while then the code comes back. I take it back apart and the exhaust cam is out of time. When we had the heads done they ground the valve seats and installed all new valves and new valve seals.

[avguy]

I can't discuss any specific timing procedural aspects, because I've only done belts on my '05 and '06. The '09 uses a different set of part numbers, and so I don't want suggest something that may be wrong for an '09.
But I will ask did you replaced all 4 timing belt components? From many prior posts, it's been fairly well established that these timing failures are typically caused by component pulley or bearing failures, or installation errors, rather than the belt itself failing. So if there is still an old pulley or the WP in the mix, that might explain what's happening with this Aveo.