•  
    Results 1 to 5 of 5

    Thread: ecu programming

    1. #1
      I'll keep it and add a turbo
      Join Date
      Jan 2015
      Location
      Egypt
      Posts
      173
      Thanks
      49
      Thanked 2 Times in 2 Posts

      ecu programming

      my chevy aveo 2009 ls A/c provision. I bought everything and I install a/c but it did not work from the HAVC control. When I make short circuit from the a/c switch it works.
      The question here the ecu need to be reprogrammed for a/c work and if yes how I can do that and how I can get the software.
      my ecu is programmable.Name:  DSC_0287.jpg
Views: 3797
Size:  292.9 KBName:  DSC_0287.jpg
Views: 3797
Size:  292.9 KB



    2. #2
      Aveo Whisperer 06T200's Avatar
      Join Date
      Aug 2014
      Location
      530
      Posts
      625
      Thanks
      56
      Thanked 90 Times in 77 Posts
      Your model of ECU is different from the ones here in the states, so I am not familiar with your model. Each year is different and I only know the 06 MT-34 firmware. If you have access to a Tech-2 and you have the service programming module, it will read the VIN and you should be able to pull down the current code and flash it. If you just want to hack the code you have, you will need to figure out how to bypass the seed/key's, (unlock the $AE PID's) then pull the code, disassemble it and spend days sifting through hex frames. Not for the faint hearted and beyond the scope of most end users. FYI

    3. #3
      Aveo Whisperer 06T200's Avatar
      Join Date
      Aug 2014
      Location
      530
      Posts
      625
      Thanks
      56
      Thanked 90 Times in 77 Posts
      If you are brave enough to 'deep dive' your PCM, and you have the moxy to do it, go here: https://hackedecu.com/

      Good luck!

    4. #4
      I'll keep it and add a turbo
      Join Date
      Jan 2015
      Location
      Egypt
      Posts
      173
      Thanks
      49
      Thanked 2 Times in 2 Posts
      Quote Originally Posted by 06T200 View Post
      Your model of ECU is different from the ones here in the states, so I am not familiar with your model. Each year is different and I only know the 06 MT-34 firmware. If you have access to a Tech-2 and you have the service programming module, it will read the VIN and you should be able to pull down the current code and flash it. If you just want to hack the code you have, you will need to figure out how to bypass the seed/key's, (unlock the $AE PID's) then pull the code, disassemble it and spend days sifting through hex frames. Not for the faint hearted and beyond the scope of most end users. FYI
      the engine I swapped is originally imported from USA. So I will try to just activate the A/C on ecu by using Tech2 tool.

    5. #5
      I'll keep it and add a turbo
      Join Date
      Jan 2015
      Location
      Egypt
      Posts
      173
      Thanks
      49
      Thanked 2 Times in 2 Posts
      thanks a lot I reviewed a previous post and knowing that the A/C can be activated by tech2 and the activation done in 2 min and the A/c works well. Everything is Ok but the engine rattling and has a little bet noise in idel only. I ask if I need to clean the throttle body or make idle learning where I just replace the sparks plugs after i swapped the engine 2 months ago.





    Similar Threads

    1. Replies: 0
      Last Post: 06-19-2015, 03:28 PM
    2. Programming new key
      By bgreeneee in forum General Discussion
      Replies: 3
      Last Post: 04-01-2014, 08:37 PM
    3. programming 2010 Aveo5 LT FOB keys????!!!
      By boopbettyx in forum Troubleshooting and Maintenance
      Replies: 1
      Last Post: 08-10-2013, 03:09 AM
    4. Replies: 1
      Last Post: 08-21-2012, 08:35 AM

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •