•  
    Page 1 of 2 12 LastLast
    Results 1 to 10 of 14

    Thread: Head bolt torque and sequence

    1. #1
      Should I keep it?
      Join Date
      May 2011
      Location
      oklahoma city
      Posts
      33
      Thanks
      0
      Thanked 0 Times in 0 Posts

      Head bolt torque and sequence

      aNYONE HAVE A WRITE UP OR KNOW THE TORQUE SPECS? THANKS.

      **Edit sry for caps lock



    2. #2
      What's wrong with my car?
      Join Date
      Apr 2011
      Location
      pa
      Posts
      9
      Garage empty: add car
      Thanks
      0
      Thanked 0 Times in 0 Posts
      According to my manual the removal and the replacement sequence are different. Removal (looking from the cam sprockets )
      headbolt 1-3-9-5-7 are on the left and 2-4-10-9-8 are on the right. Remove in that progression.
      Instillation 9-5-1-3-7 are on the left and 10-6-2-4-8 are on the right tighten in that order.
      Tighten to 25Nm or 18 ft/lb. and retighten the cyl hd blt 70 deg plus 70 deg plus 50 deg using the angular torque guage KM-470-B.
      Hope this helps. Might help to make a sketch and label the 5 headbolts on each side.

    3. #3
      Should I keep it?
      Join Date
      May 2011
      Location
      Glendale, AZ
      Posts
      45
      Thanks
      0
      Thanked 0 Times in 0 Posts
      Follow this link...
      i would like torque specs on head bolts and cam shaft ... - JustAnswer
      Shows proper order and torque

    4. #4
      What's wrong with my car?
      Join Date
      Sep 2012
      Location
      Surrey, BC
      Posts
      19
      Thanks
      0
      Thanked 0 Times in 0 Posts
      Go to AutoZone website and create an account. The info for Chevy Aveo is pretty good, was my primary source, when doing an engine swap. They have free online manuals for many cars.

      Will have a pic for head bolt removal/ installation as well as torque/ angle specs

    5. #5
      2005 best in class
      Join Date
      Jan 2012
      Location
      NY
      Posts
      61
      Thanks
      1
      Thanked 0 Times in 0 Posts
      I believe its different for diff years so be careful if you do it wrong you'll destroy the heads. You MUST use new head bolts for this procedure!!!Get the shop manual for your year and you won't go wrong plus you'll have tons of info for other issues.....

    6. #6
      What's wrong with my car?
      Join Date
      Feb 2014
      Location
      melbourne florida
      Posts
      6
      Thanks
      0
      Thanked 0 Times in 0 Posts
      The GM torque guidelines are as follows for the 05 aveo. 18 foot pounds then 60 degrees then sixty degrees then sixty degrees then at last 10 degrees. I have seen all over the place missing that last 60 degrees. Its not a lot and maybe it will never give you issues. But this is from the GM specks at the dealership.

    7. #7
      What's wrong with my car?
      Join Date
      Aug 2015
      Location
      Toronto, Ontario
      Posts
      20
      Thanks
      0
      Thanked 0 Times in 0 Posts
      Quote Originally Posted by nova321fl View Post
      The GM torque guidelines are as follows for the 05 aveo. 18 foot pounds then 60 degrees then sixty degrees then sixty degrees then at last 10 degrees. I have seen all over the place missing that last 60 degrees. Its not a lot and maybe it will never give you issues. But this is from the GM specks at the dealership.
      Does someone mind explaining the 60 degrees + 60 degrees + 10 degrees procedure?

      So I tighten the bolts to 18 foot pounds each, in the sequence order provided. BUT then I make 60 degree turns on each bolt afterwards? or is it you turn each bolt 60 degrees at a time? I am a bit confused by this.

    8. #8
      Should I keep it?
      Join Date
      Nov 2015
      Location
      Belpre, OH
      Posts
      76
      Thanks
      0
      Thanked 24 Times in 20 Posts
      You need a torque angle gauge - my local autozone sells them for about 10 bucks.

      Great Neck Torque angle meter 25424- Read6Reviews onGreat Neck #25424

      As mentioned, only use brand spanking new bolts - these are considered "torque to yield", and can NOT be reused safely.

      Following the torque sequence, tighten all bolts to 18 ft lb - now put the torque wrench away (using it to do the next steps can actually damage the wrench)

      Using your angle gauge and a breaker bar, and again following the torque sequence, turn all bolts an additional 60 degrees of rotation.

      Do that step again, turning each bolt an additional 60 degrees of rotation.

      Do that step again, turning each bolt an additional 60 degrees of rotation.

      Do that step again, but this time only turn each bolt a additional 10 degrees of rotation.

      The purpose of stepping through in so many little steps is to prevent over-stretching the bolts unevenly - bolts actually hold in tension by slight stretching, the torque to yield design stretches them ALMOST to the point of breaking; providing maximum clamping force.

    9. #9
      I'll keep it and add a turbo
      Join Date
      Jan 2016
      Location
      Vancouver, Wa.
      Posts
      109
      Thanks
      0
      Thanked 9 Times in 9 Posts
      Has anybody used head studs? or do they even make them?

    10. #10
      Should I keep it?
      Join Date
      Nov 2015
      Location
      Belpre, OH
      Posts
      76
      Thanks
      0
      Thanked 24 Times in 20 Posts
      If I were going to stud an engine, I would be looking at ARP exclusively - and they only make a kit for the Ecotec 2.2 engine. You might be able to find studs that are the right length and make it work, but would be more trouble and expense than it's worth, IMO.





    Page 1 of 2 12 LastLast

    Similar Threads

    1. Torque Mount Stiffening
      By exodus0784 in forum Engine & Drivetrain
      Replies: 4
      Last Post: 02-28-2011, 09:27 PM
    2. Ultimate bolt-on
      By zaklax13 in forum General Discussion
      Replies: 4
      Last Post: 11-14-2010, 05:27 AM
    3. Bolt pattern
      By gsills in forum Wheels, Tires, Brakes & Suspension
      Replies: 12
      Last Post: 11-19-2008, 05:51 AM
    4. What's the bolt thread?
      By subachad in forum Wheels, Tires, Brakes & Suspension
      Replies: 6
      Last Post: 06-07-2007, 04:41 PM
    5. stiffy torque damper
      By AVE0SAM in forum Engine & Drivetrain
      Replies: 2
      Last Post: 12-12-2006, 02:35 AM

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •