•  
    Page 1 of 2 12 LastLast
    Results 1 to 10 of 17

    Thread: 2017 Mods and fixes

    1. #1
      Almost time to do my timing belt xintersecty's Avatar
      Join Date
      Sep 2010
      Location
      West Union, SC
      Posts
      1,687
      Thanks
      86
      Thanked 181 Times in 156 Posts

      2017 Mods and fixes

      In 2015, I lowered the car and did some body fixes (http://www.aveoforum.com/forum/f81/b...ck-dead-16085/)
      In 2016, I replaced my head (http://www.aveoforum.com/forum/f82/e...top-end-19864/)

      AND NOW 2017!
      This is my repair log for 2017. I need to fix some stuff, do some body work, get back to doing my inside mods. Basically all the stuff that I started doing but did not finish from bringing my car back from the dead in 2015.

      I was driving in Atlanta and went over a HARD A$$ bump that tore my front ground effect.

      Name:  2016-12-08 16.52.49.jpg
Views: 2632
Size:  303.1 KB

      I have removed my front bumper and started working on it. I glued back the honda civic ground effect and pop some more rivets. Now it's the bondo sand game. Is there an APP for this?
      Name:  2017-01-20 08.28.35.jpg
Views: 1051
Size:  279.8 KBName:  2017-01-20 08.28.58.jpg
Views: 1059
Size:  286.9 KB

      When I did the work the first time, it was a bit wavy. Now I have a long sanding board and going to do it right!

      Here is my list!
      Outside
      1) Repair and fix front bumper.
      2) Fix the lights and secure the wiring better
      3) Fix the broken windshield
      4) Fix the various dings on the car
      5) Replace the passenger rear door.
      6) Cut out the running board passenger side.
      7) Weld in a new metal
      Might do a new ground effect for the rear bumper
      9) Might do side effect running boards
      10) Replace hood
      11) Paint entire car

      Inside
      1) Fix rear back up lights
      2) run cable for rear camera
      3) Get rear camera working
      4) Get receiver mounted (it's just sitting in there)
      5) Wire up recorder for rear camera
      6) Wire up dash cam


      Please do not power off, firmware update pending.....

    2. The Following User Says Thank You to xintersecty For This Useful Post:

      Daox (01-24-2017)

    3. #2
      The Lowest Static Aveo Melveo's Avatar
      Join Date
      Jan 2016
      Location
      Raleigh NC
      Posts
      256
      Thanks
      0
      Thanked 25 Times in 22 Posts
      Wow, I really like the civic front lip, too bad I would probably destroy it at my height. Name:  IMG_0014.jpg
Views: 1036
Size:  302.0 KBDo some dodge charger side skirts like mine.Name:  IMG_0006.jpg
Views: 925
Size:  8.2 KB

    4. #3
      Almost time to do my timing belt xintersecty's Avatar
      Join Date
      Sep 2010
      Location
      West Union, SC
      Posts
      1,687
      Thanks
      86
      Thanked 181 Times in 156 Posts
      Can't see the details on the side skirts. What is a charger side skirt. Alas google was no help.
      Please do not power off, firmware update pending.....

    5. #4
      The Lowest Static Aveo Melveo's Avatar
      Join Date
      Jan 2016
      Location
      Raleigh NC
      Posts
      256
      Thanks
      0
      Thanked 25 Times in 22 Posts
      06 dodge charger sideskirts, mounted up side down and (left on right side)(right on left side) that body style atleast

    6. The Following User Says Thank You to Melveo For This Useful Post:

      xintersecty (01-23-2017)

    7. #5
      Almost time to do my timing belt xintersecty's Avatar
      Join Date
      Sep 2010
      Location
      West Union, SC
      Posts
      1,687
      Thanks
      86
      Thanked 181 Times in 156 Posts
      Melvo, would love some detail pictures on those side skirts and how did you mount them?


      Today's work. First we start with a blood sacrifice with the gods to ensure project success. It's important to use a high speed orbital sander to rough up the plastic while burning the skin off your knuckle.
      Name:  2017-01-24 12.40.07.jpg
Views: 925
Size:  282.6 KB

      I used the ends off the civic bumper to make better looking conclusion to the aveo/civic bumper combo. Sanded and prep before mounting them again.
      Name:  2017-01-24 12.40.30.jpg
Views: 965
Size:  276.0 KB

      Sorry for the bad focus
      Name:  2017-01-24 13.10.19.jpg
Views: 950
Size:  281.3 KB

      The other side and better focus
      Name:  2017-01-24 13.11.12.jpg
Views: 954
Size:  288.1 KB

      I use a slurry of 5 min epoxy and micro balloons. It sands down nice and gives it thickness that does not run. That's the white stuff for the glue.
      Please do not power off, firmware update pending.....

    8. The Following User Says Thank You to xintersecty For This Useful Post:

      Daox (01-24-2017)

    9. #6
      Administrator Daox's Avatar
      Join Date
      Jan 2007
      Location
      Wisconsin
      Posts
      2,523
      Thanks
      172
      Thanked 92 Times in 80 Posts
      Repairs are looking good!

    10. #7
      Almost time to do my timing belt xintersecty's Avatar
      Join Date
      Sep 2010
      Location
      West Union, SC
      Posts
      1,687
      Thanks
      86
      Thanked 181 Times in 156 Posts
      OK Today's report.

      Here is the current status of the bumper and front bumper mod.
      Name:  2017-01-25 07.54.04.jpg
Views: 887
Size:  292.8 KB

      Now I need to sand and putty putty sand sand. I should be able to start priming by friday.

      OK, I had mentioned that my windshield was broken. I was driving from Atlanta and needed COFFEE. It was 6:00AM in the morning and I pulled into commerce. I missed the Starbucks and drove into a parking lot to safely pull around. Between the backlights and color, I ran into this:
      Name:  2016-09-26 05.41.19.jpg
Views: 842
Size:  284.6 KB

      It did this damage to my car:
      Name:  2017-01-24 17.38.38.jpg
Views: 844
Size:  286.8 KB

      And cracked the window:
      Name:  2017-01-24 17.47.57.jpg
Views: 893
Size:  290.7 KB

      So I started pulling out the A pillar. That is some tough steel there.
      Name:  2017-01-24 17.47.50.jpg
Views: 879
Size:  281.8 KB
      Please do not power off, firmware update pending.....

    11. #8
      The Lowest Static Aveo Melveo's Avatar
      Join Date
      Jan 2016
      Location
      Raleigh NC
      Posts
      256
      Thanks
      0
      Thanked 25 Times in 22 Posts
      More info on the skirts. They are just self tapped to the body with a support beam in the front, still working on how the rear will fit.\Name:  IMG_0471.jpg
Views: 831
Size:  269.6 KBName:  IMG_0473.jpg
Views: 880
Size:  288.7 KBName:  IMG_0475.jpg
Views: 859
Size:  286.2 KB
      The top is from under a charger/chysler 300, either will do. You can tell the bottom of the skirt is really the top of it when you mount it on the car. The gaps along the skirt similar to the middle picture, you grind/shave smooth so it mounts flush to the body.Name:  16105634_10206639344137059_8973167882225855614_n.jpg
Views: 851
Size:  28.6 KB Pic after i first did it, gives maybe 2-3 inches visable lower, dont worry about dragging them, they will compress under the body then just fold back out. Pic on stock wheels. SLAMMED lolName:  IMG_0014.jpg
Views: 842
Size:  300.3 KB
      Attached Images Attached Images   
      Last edited by Melveo; 01-25-2017 at 03:41 PM.

    12. #9
      Almost time to do my timing belt xintersecty's Avatar
      Join Date
      Sep 2010
      Location
      West Union, SC
      Posts
      1,687
      Thanks
      86
      Thanked 181 Times in 156 Posts
      Latest work:

      I drilled a hole to knock the backside of some bent metal on the glass side (sorry for the dark pictures)
      Name:  2017-02-01 19.48.57.jpg
Views: 797
Size:  290.3 KB

      Welded the hole closed
      Name:  2017-02-01 20.09.12.jpg
Views: 782
Size:  288.8 KB

      Now some filler and sanding
      Name:  2017-02-03 13.00.16.jpg
Views: 781
Size:  287.9 KB

      Any suggestions on removing the glass? Looks I need to in order to do the repair right.
      Please do not power off, firmware update pending.....

    13. #10
      Almost time to do my timing belt xintersecty's Avatar
      Join Date
      Sep 2010
      Location
      West Union, SC
      Posts
      1,687
      Thanks
      86
      Thanked 181 Times in 156 Posts
      Sorry no pictures of the front fender. Work on that is going well and getting closer to final paint. Meanwhile here is the progress on the passenger A column.

      Name:  2017-02-05 09.10.53.jpg
Views: 744
Size:  290.0 KB

      First coat of spray can primer.
      Name:  2017-02-05 09.36.45.jpg
Views: 771
Size:  291.3 KB

      Any suggestions on the glass?




      Please do not power off, firmware update pending.....

    Page 1 of 2 12 LastLast

    Similar Threads

    1. Replies: 1
      Last Post: 03-20-2017, 07:55 PM
    2. Strut tower rusted out / any fixes ?
      By toppertopper in forum General Discussion
      Replies: 7
      Last Post: 07-10-2014, 03:49 AM
    3. Radiator Leaks and Chemical Fixes
      By sonanova in forum Troubleshooting and Maintenance
      Replies: 4
      Last Post: 03-01-2014, 11:20 PM
    4. Replies: 6
      Last Post: 09-22-2013, 05:14 AM

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •