Is the stock fog light button mounted on that card slot on the door or where is it? i want to hook the lights up just like stock but i want RED led bulbs in the fog light housing and underbody glow as well on the switch wherever it hooks up.
Printable View
Is the stock fog light button mounted on that card slot on the door or where is it? i want to hook the lights up just like stock but i want RED led bulbs in the fog light housing and underbody glow as well on the switch wherever it hooks up.
my fog light switch is on the turn signal arm.
the buttom on the drivers door above the card slot is the control for the passenger power side view mirror.
I think Nemasys put his fog swith there??? not sure exactly, but I know someone did.
I remember seeing somewhere that the switch was to the left of the hazard button, but Im not sure if that was stock. I put my switch where your talking about(about slot) and it looks very stock and was a snap to install and run wires.
http://memimage.cardomain.net/member...43_13_full.jpg
http://memimage.cardomain.net/member...43_14_full.jpg
You can alos get the switch in red like you want. I got it at Autozone.
how much does the set cost for the fog lights?? thats 1 more project for my car down the road.
Sorry Blade..it was your car not Nems
thanks your switch looks great. i didnt buy the lights myself they were a present but i will ask when my dad gets home but they came from the dealership.
No prob. man.Quote:
Originally Posted by Ron-E-Babe
As for price, I think I payed like $110 for my OEM fogs, but I think that was with my employee discount. Either way, I dont think they were that expensive being OEM.
I have found oem fog lights and a new oem light switch but I haven't seen wiring for fog lights as my car was never equipped with them. How should I go about wiring in some factory fog lights?
Just like this. Autozone should have their parts with their foglights, thats where i got mine. get a wire kit with a rocker and a relay. Both of mine were "pilot" brand. Also, if you arent doing a lighted rocker (which i would seriously recommend so you dont leave youre lights on) then you dont need to ground the switch
http://www.offroaders.com/info/tech-...ay-diagram.gif
i agree with pickles, i used a relayed harness kit i bought and ran my own wires, and got pigtails and such to hook into the oem switch and fog lights.
Quote:
Originally Posted by petrified.rabbit
So you were able to successfully wire the after market harness to the oem switch? Did you connect it to the fuse box? I found the switch I want but I'm just trying to make sure I can do this before I buy it. Here is a link to it. Thanks!
2004-2008 Chevrolet Aveo Headlight Switch - Body Electrical - Standard Motor Products 04-08 Aveo Headlight Switch - 17824-07035453 - PartsGeek
So I finally got all of my parts and began my oem fog light install on my '06 aveo hb. I started by removing the driver side wheel and then the plastic fender well liner. Then I removed half of the screws and bolts holding the bumper on to allow me to reach the plastic covers where the fog lights are going. I did not want to have to remove the entire bumper so this was very tight. But I managed to pull the plastic covers and install the new fogs with very little trouble. I repeated this process on the passenger side. I just started wiring them in with a universal harness and I'm going to run the on/ off cable to the new factory turn/headlight/high beam/ fog switch I bought as I wanted them to appear factory.
http://s12.postimg.org/gw39ee77t/image.jpg
http://s12.postimg.org/ur1jwv1mx/image.jpg
http://s12.postimg.org/idoppybyh/image.jpg
http://s12.postimg.org/3vrihyknd/image.jpg
http://s12.postimg.org/mcqimipzd/image.jpg
http://s12.postimg.org/6frqpsxl5/image.jpg
http://s12.postimg.org/7jbv1ri89/image.jpg
http://s12.postimg.org/qcxnyrgg9/image.jpg
This ended up being far easier then I had imagined. The new oem switch with the fogs just had two extra wires that ran to the fog lights. I simply determined which wires were for the turn signals, head lights and high beams and left them intact with the pig tail so that they operated normally. Then I cut the two wires for the fog lights and spliced them to the after market wiring harness. Voila! Illumination.
Looks great im trying to figuer out some what the same issue but im only running one fog lamp. BTW love those projectors
Looks nice , now tint them Jdm Gold :cool:
Anyone know where to find the OEM switch that goes beside the hazards?
Dealer, E-bay, Scrap yard near you LKQ,