Printable View
Hi everyone, I'm new to the site. I have an aveo with manual locks and Windows. I found on craigslist an aveo with power locks and windows that was being parted out. Can i take those doors? Is there a harness anywhere in my car to allow me to do this. Also i have a sedan, his was a hatchback. The doors look identical. Thanks.
If the doors were to physically fit, which they probably won't due to differences in roof line, you can run into a nightmare getting them to work. Aside from the necessary harnesses, you will need the correct Body Control Module to run them. The car will need to accept the BCM. If your car has equipment or is missing equipment from what the donor car had, even with a reflash, it may not work due to compatibility or Can-Buss issues. It is a lot of hassle and only you can decide if the end result is worth it. You may want to research aftermarket window/lock kits.
im not sure how far out the universal harness extends year to year, if you are seriously considering this, the get a wiring diagram and see how far out the wiring exists, if it does.
Based on my research for the fog lights addition, the wiring should have been there, it was not.
I just bought a kit on ebay to convert locks and windows to automatic, since i was in the same predicament as you. installation includes taking off door panels(plastic inside), wiring things up and putting door panel back on.
it would help to know what year and Body Style you have, as it would make our advice A LOT easier to give. and to Rabbit; I've done some Research of my own while diagnosing my Oxygen Sensor Problem. I have a Wiring Diagram of the Aveo Sedan's Fog Lamp Circuit, and the Ambient Temperature Sensor for the DIC, as well as the pinouts for all of the connectors involved. from what i've seen by looking under Scoots' Dash and Driver's Side Kickpanel, I believe at least the 1LT Aveos are Pre Wired for Fog Lamps all the way to the Underhood Fuse Box. if it would Appease the Court, I can Upload the Diagrams and Connector Pinouts in question.Quote:
Originally Posted by ave07
Thank You for the response. I probably won't do it now. I was curious just to see if I could just remove and replace. I'm aware of the kits. Have you ever installed one? I couldn't find one in the how to section. ThanksQuote:
Originally Posted by thankful_ragamuffin
I'm going to replace the locks and windows next weekends...I'll take pics and post them once I have it done
That would be awesome man. Thank you.Quote:
Originally Posted by jman765
Quote:
Originally Posted by 2010AveoLT
If you can that would be good or email them to me at jbetancourt01@gmail.com.... Im thinking about getting the fog lamps for my 11 Aveo, but can't find them on Ebay....
I have the same car as you and i got my fog lights off ebay for like 95$ comes with everything you need.Quote:
Originally Posted by metroII
2007 2011 Chevy Aveo 4DR Fog Lights 07 08 Pontiac G3 w Wiring Kit Instruction | eBay Enjoy :D
Edit: Homie helping me install it.
probably easier to make your own kit
http://i112.photobucket.com/albums/n...s52efdf7f.jpegQuote:
Originally Posted by metroII
this is the Fog Lamp Wiring Diagram
http://i112.photobucket.com/albums/n...pse6d316fe.jpg
This is Connector X207; its behind the Driver's Side (or Passenger Side for RHD Models) Kick Panel. if you trying to add the Ambient Temperature Sensor for your Driver Information Center, this is the Connector you need to seek because the Pre Wiring done at the Factory Terminates here. and BE CAREFUL, the Wiring for the Front SIR Discriminating Sensors runs through this connector as well.
http://i112.photobucket.com/albums/n...psf68695c7.jpg
this is the Connector Layout of the Underhood Bussed Electrical Center (UBEC) (Ignore the Lines and Numbers on Connectors X1 and X2, those numbers correspond to the Downstream Oxygen Sensor Circuit)
http://i112.photobucket.com/albums/n...ps87463091.jpg
this is the layout of UBEC Connector X2; Pin Number 1 Provides the Control Voltage for the Fog Lamps. the blacked out areas indicate the pins that are not Used.
http://i112.photobucket.com/albums/n...pse7bb3896.jpg
to make finding the Right Wire easier, here is Connector X2's Pinout List.
http://i112.photobucket.com/albums/n...ps6e2a6e12.jpg
This is the Layout of UBEC Connector X3, this is where most of the Fog Lamp Wiring Passes Through the UBEC. the Connector Pins to Single out are Pins 14, 15, and 16.
http://i112.photobucket.com/albums/n...ps1a45ee63.jpg
Connector X2's Pinout List; I've made notes on which Pin and Circuit Does what for the Fog Lamps.
Hope this Helps!
Dude, how tall is your friend? my headlight sits at my knee.. its above his waist.Quote:
Originally Posted by molokaiboi
Lmao he's like 5'5-5'8 or something hahaa. He's 30 but look 14 lmaoQuote:
Originally Posted by petrified.rabbit